Rim (firearms)

thumb|right|Rimmed vs rimless cartridges

A rim is an external flange that is machined, cast, molded, stamped, or pressed around the bottom of a firearms cartridge. Thus, rimmed cartridges are sometimes called "flanged" cartridges. Almost all cartridges feature an extractor or headspacing rim, in spite of the fact that some cartridges are known as "rimless cartridges". The rim may serve a number of purposes, including providing a lip for the extractor to engage, and sometimes serving to headspace the cartridge.

Types

There are various types of firearms rims in use in modern ammunition. The main types are categorized as rimmed, rimless, semi-rimmed, rebated, and belted. These describe the size of the rim in relation to the base of the case.

thumb|right|Rimmed .357 Magnum revolver ammunition

Rimmed

The rimmed cartridge, sometimes called flanged cartridge, is the oldest of the types and has a rim that is significantly larger in diameter than the base of the cartridge. Rimmed cartridges use the rim to hold the (usually straight sided) cartridge in the chamber of the firearm, with the rim serving to hold the cartridge at the proper depth in the chamber—this function is called "headspacing". Because the rimmed cartridge headspaces on the rim, the case length is of less importance than with rimless cartridges. Rimmed cartridges with straight walls, such as shotgun shells, allow various lengths of the same cartridge to be chambered in the firearm; if the round protrudes into the rifling of the barrel past the length of the chamber, the rifling can act as a fluted chamber to ease extraction.

This allows some firearms chambered for similar rimmed cartridges to safely chamber and fire shorter cartridges, such as using .38 Special cartridges in a .357 Magnum revolver, as these are the same diameter despite the nomenclature. Rimmed cartridges are well suited for certain types of actions, such as revolvers and break-action firearms, where the rim helps hold the cartridge in position.

Rimmed cartridges generally do not work quite as well in firearms that feed from a box magazine, since the magazine must be carefully loaded so that the rim from each successive case is loaded ahead of the round beneath it, so the round will not snag on the rim of the cartridge below it as the bolt strips it out of the magazine. However, box magazine firearms firing rimmed cases have seen extensive use; the famous Lee–Enfield rifle used by the UK, and the Russian Mosin-Nagant rifle which uses an interrupter to help prevent the snags, were both used from before World War I until after World War II. Semi-automatic handguns have been chambered in rimmed cartridges as well, for example a LAR Grizzly or Desert Eagle in .357 Magnum or .44 Magnum. The .22 Long Rifle is extremely popular in semi-automatics.

Rimmed cartridges work with belt-fed machine guns that use a two stage pull out – push through feeding operation, notably the Maxim gun, Vickers, M1919 Browning and M2HB. Push through links are possible with rimmed cartridges using specially designed belt links, but not as reliable as using push through links with rimless ammunition.

Rimfire cartridges also use the rim to contain the priming compound to ignite the cartridge instead of a centrally mounted primer, as is commonly used in centerfire cartridges.

Under the metric cartridge designation system, a capitalized "R" added at the end of the designation denotes a rimmed cartridge. For example, "7.62×54mmR" is a rimmed cartridge, while "7.62×51mm" is a rimless cartridge. Under imperial or US customary designations, there is typically no distinction between rimmed and unrimmed cartridges, unless one is referring to a rimmed version of a cartridge which is typically rimless, such as the .45 Auto Rim, a special rimmed version of the .45 ACP ("Automatic Colt Pistol" aka ".45 Auto"), intended for use in M1917 service revolvers.

Examples of rimmed handgun cartridges include the .38 Special, .357 Magnum, .44 Special, .44 Magnum, .45 Schofield, and .45 Colt. Rimmed rifle cartridge examples include the .22 Hornet, .30-30 Winchester, 7.62×54mmR, .303 British, 8×50mmR Lebel, and .45-70 Government.

thumb|right|Rimless 9mm Parabellum pistol cartridges

Rimless

As early as 1867 Joseph Whitworth patented a round which "has a solid metal back without any projecting flange, as heretofore, the ring groove already mentioned being a substitute for it". Even though some rifles were designed for rimless cartridges by Bethel Burton, Eduard Rubin and others, the first adoption did not come until 1888 with the German Patrone 88.

The rim on a "rimless" case is almost or exactly the same diameter as the base of the case. A recess formed between the rim and the body of the cartridge is known as an extractor groove, allowing the case to be grasped by an extractor after being fired. Since there is no rim projecting past the edge of the case, the cartridge must headspace on the case mouth, for a straight walled case, or on the case's shoulder for a bottlenecked case (although a bottlenecked case can headspace on the case mouth, depending on the cartridge); the extractor groove serves only for extraction. The lack of a projecting rim makes rimless cases feed very smoothly from box magazines, drum magazines, and belts. Rimless cases are not well suited to break-open and revolver actions, though in break-action firearms they can be used with appropriate modifications, such as a spring-loaded extractor/ejector or, in a revolver, a half or full moon clip (for example, the Colt or Smith & Wesson M1917 revolvers in .45 ACP).

Semi-rimmed

thumb|right|Semi-rimmed .32 ACP pistol cartridges

On a semi-rimmed case the rim projects slightly beyond the base of the case, though not as much as a rimmed cartridge. The tiny rim provides minimal interference feeding from a box magazine, while still providing enough surface to headspace on. Semi-rimmed cases are less common than the other types.

Examples of semi-rimmed handgun cartridges are .25 ACP, .32 ACP, 8×22mm Nambu, .38 ACP, .38 Super, and 9mm Browning Long. Semi-rimmed rifle examples include the .220 Swift, .280 Ross, 6.5×50mm Arisaka, .308 Marlin Express, .338 Marlin Express, and .444 Marlin.

The only known shotgun shells using rebated rims is the Roper repeating shotgun and the 12 Gauge RAS12, specially made for the RAS-12 semi-automatic shotgun.

The .50 Beowulf rifle cartridge uses a rebated-rim design. This round is used in specialized AR-15 upper receivers, and the rim matches the size of the rim of the 7.62×39mm, allowing those parts to be used in the custom-built upper receivers. A telescopic example existed, the 23×260mm round used in the Rikhter R-23 autocannon that operated in a similar way.

Belted

thumb|Belted .375 H&H Magnum (left), .338 Winchester Magnum (right), [[Quarter (United States coin)|US quarter (24 mm) for scale]]

The original purpose of the "belt" on belted cases (often referred to as belted magnums) was to provide headspacing; the extractor groove is cut into the belt just as it is cut into the case head on a rimless case. The belt acts as a rim on what is essentially a rimless case. The design originated in England around 1910 with the .400/375 Belted Nitro Express (also known as the .375/.400 Holland & Holland, and .375 Velopex). The addition of the belt allowed the cartridge to properly headspace, despite the relative lack of a definite shoulder. The reason for the lack of a definitive shoulder was that these old British cartridge cases were intended for firing cordite charges instead of modern smokeless powder. Cordite was extruded as spaghetti-like rods, so the cartridge cases had to be fairly cylindrical shaped to accommodate the cordite propellant rods. The belt was carried through on other cartridges derived from the .375 Velopex, like the belted .375 Holland & Holland Magnum of 1912, in some cases to allow the cartridge to function in bolt-action rifles (the original .375 H&H Magnum was a rimmed case for use in double-barreled rifles), or to prevent the higher-pressure magnum cartridge from accidentally being chambered in a gun with a chamber of similar size.

Examples of belted handgun cartridges include the .40 BSA Auto Pistol and .40 G&A Magnum. Belted rifle / machine gun examples include the .224 Weatherby Magnum, .300 Winchester Magnum, .375 H&H Magnum, .450 Marlin, .458 Lott, 13×64mmB and .55 Boys.

In the United States, the belt became somewhat synonymous with "magnum" during the late 20th century. More recently, new "magnum" cartridges introduced in the United States have been rimless or used rebated rims based on the .404 Jeffery that fit the same .512" bolt face used for the belted cases.