thumb|right|Temperature dependence of the relative static permittivity of water

The relative permittivity (in older texts, dielectric constant) is the permittivity of a material expressed as a ratio with the electric permittivity of a vacuum. A dielectric is an insulating material, and the dielectric constant of an insulator measures the ability of the insulator to store electric energy in an electrical field.

Permittivity is a material's property that affects the Coulomb force between two point charges in the material. Relative permittivity is the factor by which the electric field between the charges is decreased relative to vacuum.

Likewise, relative permittivity is the ratio of the capacitance of a capacitor using that material as a dielectric, compared with a similar capacitor that has vacuum as its dielectric. Relative permittivity is also commonly known as the dielectric constant, a term still used but deprecated by standards organizations in engineering

:<math> \varepsilon_\text{r}(\omega) = \varepsilon_\text{r}'(\omega) - i \varepsilon_\text{r}(\omega). </math>

The relative permittivity of a medium is related to its electric susceptibility, , as .

In anisotropic media (such as non cubic crystals) the relative permittivity is a second rank tensor.

The relative permittivity of a material for a frequency of zero is known as its static relative permittivity.

Terminology

The historical term for the relative permittivity is dielectric constant. It is still commonly used, but has been deprecated by standards organizations, because of its ambiguity, as some older reports used it for the absolute permittivity ε. that is , although there are theoretical nonlinear quantum effects in vacuum that become non-negligible at high field strengths.

The following table gives some typical values.

{|class="wikitable"

|+ Low-frequency relative permittivity of some common solvents

|-

! colspan="2" |Solvent

! Relative permittivity

! Temperature

|-

|C<sub>6</sub>H<sub>6</sub>

| benzene || 2.3 || 298 K (25&nbsp;°C)

|-

|Et<sub>2</sub>O

| diethyl ether || 4.3 || 293 K (20&nbsp;°C)

|-

|(CH<sub>2</sub>)<sub>4</sub>O

| tetrahydrofuran (THF) || 7.6 || 298 K (25&nbsp;°C)

|-

|CH<sub>2</sub>Cl<sub>2</sub>

| dichloromethane || 9.1 || 293 K (20&nbsp;°C)

|-

|NH<sub>3</sub>(liq)

| liquid ammonia || 17 || 273 K (0&nbsp;°C)

|-

|C<sub>2</sub>H<sub>5</sub>OH

| ethanol || 24.3 || 298 K (25&nbsp;°C)

|-

|CH<sub>3</sub>OH

| methanol || 32.7 || 298 K (25&nbsp;°C)

|-

|CH<sub>3</sub>NO<sub>2</sub>

| nitromethane || 35.9 || 303 K (30&nbsp;°C)

|-

|HCONMe<sub>2</sub>

| dimethyl formamide (DMF) || 36.7 || 298 K (25&nbsp;°C)

|-

|CH<sub>3</sub>CN

| acetonitrile || 37.5 || 293 K (20&nbsp;°C)

|-

|H<sub>2</sub>O

| water || 78.4|| 298 K (25&nbsp;°C)

|-

|HCONH<sub>2</sub>

| formamide || 109 || 293 K (20&nbsp;°C)

|}

The relative low frequency permittivity of ice is ~96 at −10.8&nbsp;°C, falling to 3.15 at high frequency, which is independent of temperature. It remains in the range 3.12–3.19 for frequencies between about 1&nbsp;MHz and the far infrared region.

Determination

The relative static permittivity, ε<sub>r</sub>, can be determined for static electric fields as follows: first the capacitance of a test capacitor, C<sub>0</sub>, is measured with vacuum between its plates. Then, using the same capacitor and distance between its plates, the capacitance C with a dielectric between the plates is measured. The relative permittivity can be then calculated as

: <math>\varepsilon_\text{r} = \frac{C}{C_0}.</math>

For time-variant electromagnetic fields, this quantity becomes frequency-dependent. An indirect technique to calculate ε<sub>r</sub> is conversion of radio frequency S-parameter measurement results. A description of frequently used S-parameter conversions for determination of the frequency-dependent ε<sub>r</sub> of dielectrics can be found in this bibliographic source. Alternatively, resonance based effects may be employed at fixed frequencies.

Applications

Energy

The relative permittivity is an essential piece of information when designing capacitors, and in other circumstances where a material might be expected to introduce capacitance into a circuit. If a material with a high relative permittivity is placed in an electric field, the magnitude of that field will be measurably reduced within the volume of the dielectric. This fact is commonly used to increase the capacitance of a particular capacitor design. The layers beneath etched conductors in printed circuit boards (PCBs) also act as dielectrics.

Communication

Dielectrics are used in radio frequency (RF) transmission lines. In a coaxial cable, polyethylene can be used between the center conductor and outside shield. It can also be placed inside waveguides to form filters. Optical fibers are examples of dielectric waveguides. They consist of dielectric materials that are purposely doped with impurities so as to control the precise value of ε<sub>r</sub> within the cross-section. This controls the refractive index of the material and therefore also the optical modes of transmission. However, in these cases it is technically the relative permittivity that matters, as they are not operated in the electrostatic limit.

Environment

The relative permittivity of air changes with temperature, humidity, and barometric pressure. Sensors can be constructed to detect changes in capacitance caused by changes in the relative permittivity. Most of this change is due to effects of temperature and humidity as the barometric pressure is fairly stable. Using the capacitance change, along with the measured temperature, the relative humidity can be obtained using engineering formulas.

Chemistry

The relative static permittivity of a solvent is a relative measure of its chemical polarity. For example, water is very polar, and has a relative static permittivity of 80.10 at 20&nbsp;°C while n-hexane is non-polar, and has a relative static permittivity of 1.89 at 20&nbsp;°C. This information is important when designing separation, sample preparation and chromatography techniques in analytical chemistry.

The correlation should, however, be treated with caution. For instance, dichloromethane has a value of ε<sub>r</sub> of 9.08 (20&nbsp;°C) and is rather poorly soluble in water (13g/L or 9.8mL/L at 20&nbsp;°C); at the same time, tetrahydrofuran has its ε<sub>r</sub> = 7.52 at 22&nbsp;°C, but it is completely miscible with water. In the case of tetrahydrofuran, the oxygen atom can act as a hydrogen bond acceptor; whereas dichloromethane cannot form hydrogen bonds with water.<!-- The commonly known "like-dissolves-like" principle could be useful here, as the probable reason for the discrepancy is the specific interaction between the oxygen atoms, as the THF could be treated as a homologue of water. -->

This is even more remarkable when comparing the ε<sub>r</sub> values of acetic acid (6.2528) and that of iodoethane (7.6177).

In the high-frequency region, which extends from radio frequencies to the far infrared and terahertz region, the plasma frequency of the electron gas is much greater than the electromagnetic propagation frequency, so the refractive index n of a metal is very nearly a purely imaginary number. In the low frequency regime, the effective relative permittivity is also almost purely imaginary: It has a very large imaginary value related to the conductivity and a comparatively insignificant real-value.

See also

  • Curie temperature
  • Dielectric spectroscopy
  • Dielectric strength
  • Electret
  • Ferroelectricity
  • Green–Kubo relations
  • High-κ dielectric
  • Kramers–Kronig relations
  • Linear response function
  • Low-κ dielectric
  • Dielectric loss
  • Permittivity
  • Refractive index
  • Permeability (electromagnetism)

References