Radio receiver

thumb|A modern [[communications receiver, used in two-way radio communication stations to talk with remote locations by shortwave radio.]]

thumb|A [[clock radio, a bedside broadcast AM and FM radio receiver combined with an alarm clock. The clock can be set to turn on the radio in the morning, to wake the owner with audio from a broadcast radio station.]]

In radio communications, a radio receiver, also known as a receiver, a wireless, or simply a radio, is an electronic device that receives radio waves and converts the information carried by them to a usable form. It is used with an antenna. The antenna responds to radio waves (electromagnetic waves of radio frequency) and converts them to tiny alternating currents which are applied to the receiver, and the receiver extracts the desired information. The receiver uses electronic filters to separate the desired radio frequency signal from all the other signals picked up by the antenna, an electronic amplifier to increase the power of the signal for further processing, and finally recovers the desired information through demodulation.

Radio receivers are essential components of all systems based on radio technology. The information produced by the receiver may be in the form of sound, video (television), or digital data. A radio receiver may be a separate piece of electronic equipment, or an electronic circuit within another device. The most familiar type of radio receiver for most people is a broadcast radio receiver, which reproduces sound transmitted by radio broadcasting stations, historically the first mass-market radio application. A broadcast receiver is commonly called a "radio". However radio receivers are very widely used in other areas of modern technology, in televisions, cell phones, wireless modems, radio clocks and other components of communications, remote control, and wireless networking systems.

Applications

Radio has many practical applications, which include broadcasting, voice communication, data communication, radar, radiolocation, medical treatments, and remote control.

Principles

thumb|upright=0.25|Symbol for an antenna

A radio receiver is connected to an antenna which converts some of the energy from the incoming radio wave into a tiny radio frequency AC voltage which is applied to the receiver's input. An antenna typically consists of an arrangement of metal conductors. The oscillating electric and magnetic fields of the radio wave push the electrons in the antenna back and forth, creating an oscillating voltage.

The antenna may be enclosed inside the receiver's case, as with the ferrite loop antennas of AM radios and the flat inverted F antenna of cell phones; attached to the outside of the receiver, as with whip antennas used on FM radios, or mounted separately and connected to the receiver by a cable, as with rooftop television antennas and satellite dishes.

Practical radio receivers perform three basic functions on the signal from the antenna:

• bandpass filtering,
• amplification, and
• demodulation

Reception

The signal strength of radio waves decreases the farther they travel from the transmitter, so a radio station can only be received within a limited range of its transmitter. The range depends on the power of the transmitter, the sensitivity of the receiver, atmospheric and internal noise, as well as any geographical obstructions such as hills between transmitter and receiver. AM broadcast band radio waves travel as ground waves which follow the contour of the Earth, so AM radio stations can be reliably received at hundreds of miles distance. Due to their higher frequency, FM band radio signals cannot travel far beyond the visual horizon; limiting reception distance to about 40 miles (64 km), and can be blocked by hills between the transmitter and receiver. However FM radio is less susceptible to interference from radio noise (RFI, sferics, static) and has higher fidelity; better frequency response and less audio distortion, than AM. So in countries that still broadcast AM radio, serious music is typically only broadcast by FM stations, and AM stations specialize in radio news, talk radio, and sports radio. Like FM, DAB signals travel by line of sight so reception distances are limited by the visual horizon to about 30–40 miles (48–64 km).

Bandpass filtering

thumb|upright=0.5|Symbol for a bandpass filter used in [[block diagrams of radio receivers]]

Radio waves from many transmitters pass through the air simultaneously without interfering with each other and are received by the antenna. These can be separated in the receiver because they have different frequencies; that is, the radio wave from each transmitter oscillates at a different rate. To separate out the desired radio signal, the bandpass filter allows the frequency of the desired radio transmission to pass through, and blocks signals at all other frequencies.

The bandpass filter consists of one or more resonant circuits (tuned circuits). The resonant circuit is connected between the antenna input and ground. When the incoming radio signal is at the resonant frequency, the resonant circuit has high impedance and the radio signal from the desired station is passed on to the following stages of the receiver. At all other frequencies the resonant circuit has low impedance, so signals at these frequencies are conducted to ground.

• Bandwidth and selectivity: See graphs. The information (modulation) in a radio transmission is contained in two narrow bands of frequencies called sidebands (SB) on either side of the carrier frequency (C), so the filter has to pass a band of frequencies, not just a single frequency. The band of frequencies received by the receiver is called its passband (PB), and the width of the passband in kilohertz is called the bandwidth (BW). The bandwidth of the filter must be wide enough to allow the sidebands through without distortion, but narrow enough to block any interfering transmissions on adjacent frequencies (such as S2 in the diagram). The ability of the receiver to reject unwanted radio stations near in frequency to the desired station is an important parameter called selectivity determined by the filter. In modern receivers quartz crystal, ceramic resonator, or surface acoustic wave (SAW) filters are often used which have sharper selectivity compared to networks of capacitor-inductor tuned circuits.
• Tuning: To select a particular station the radio is "tuned" to the frequency of the desired transmitter. The radio has a dial or digital display showing the frequency it is tuned to. Tuning is adjusting the frequency of the receiver's passband to the frequency of the desired radio transmitter. Turning the tuning knob changes the resonant frequency of the tuned circuit. When the resonant frequency is equal to the radio transmitter's frequency the tuned circuit oscillates in sympathy, passing the signal on to the rest of the receiver.

Amplification

thumb|upright=0.5|Symbol for an [[amplifier]]

The power of the radio waves picked up by a receiving antenna decreases with the square of its distance from the transmitting antenna. Even with the powerful transmitters used in radio broadcasting stations, if the receiver is more than a few miles from the transmitter the power intercepted by the receiver's antenna is very small, perhaps as low as picowatts or femtowatts. To increase the power of the recovered signal, an amplifier circuit uses electric power from batteries or the wall plug to increase the amplitude (voltage or current) of the signal. In most modern receivers, the electronic components which do the actual amplifying are transistors.

Receivers usually have several stages of amplification: the radio signal from the bandpass filter is amplified to make it powerful enough to drive the demodulator, then the audio signal from the demodulator is amplified to make it powerful enough to operate the speaker. The degree of amplification of a radio receiver is measured by a parameter called its sensitivity, which is the minimum signal strength of a station at the antenna, measured in microvolts, necessary to receive the signal clearly, with a certain signal-to-noise ratio. Since it is easy to amplify a signal to any desired degree, the limit to the sensitivity of many modern receivers is not the degree of amplification but random electronic noise present in the circuit, which can drown out a weak radio signal.

Demodulation

thumb|upright=0.5|Symbol for a demodulator

After the radio signal is filtered and amplified, the receiver must extract the information-bearing modulation signal from the modulated radio frequency carrier wave. This is done by a circuit called a demodulator (detector). Each type of modulation requires a different type of demodulator

• an AM receiver that receives an (amplitude modulated) radio signal uses an AM demodulator
• an FM receiver that receives a frequency modulated signal uses an FM demodulator
• an FSK receiver which receives frequency-shift keying (used to transmit digital data in wireless devices) uses an FSK demodulator

Many other types of modulation are also used for specialized purposes.

The modulation signal output by the demodulator is usually amplified to increase its strength, then the information is converted back to a human-usable form by some type of transducer. An audio signal, representing sound, as in a broadcast radio, is converted to sound waves by an earphone or loudspeaker. A video signal, representing moving images, as in a television receiver, is converted to light by a display. Digital data, as in a wireless modem, is applied as input to a computer or microprocessor, which interacts with human users.

:AM demodulation

thumb|Envelope detector circuit

thumb|How an envelope detector works

:The easiest type of demodulation to understand is AM demodulation, used in AM radios to recover the audio modulation signal, which represents sound and is converted to sound waves by the radio's speaker. It is accomplished by a circuit called an envelope detector (see circuit), consisting of a diode (D) with a bypass capacitor (C) across its output.

:See graphs. The amplitude modulated radio signal from the tuned circuit is shown at <span style="color:red;">(A)</span>. The rapid oscillations are the radio frequency carrier wave. The audio signal (the sound) is contained in the slow variations (modulation) of the amplitude (size) of the waves. If it was applied directly to the speaker, this signal cannot be converted to sound, because the audio excursions are the same on both sides of the axis, averaging out to zero, which would result in no net motion of the speaker's diaphragm. <span style="color:red;">(B)</span> When this signal is applied as input V_I to the detector, the diode (D) conducts current in one direction but not in the opposite direction, thus allowing through pulses of current on only one side of the signal. In other words, it rectifies the AC current to a pulsing DC current. The resulting voltage V_O applied to the load R_L no longer averages zero; its peak value is proportional to the audio signal. <span style="color:red;">(C)</span> The bypass capacitor (C) is charged up by the current pulses from the diode, and its voltage follows the peaks of the pulses, the envelope of the audio wave. It performs a smoothing (low pass filtering) function, removing the radio frequency carrier pulses, leaving the low frequency audio signal to pass through the load R_L. The audio signal is amplified and applied to earphones or a speaker.

Automatic gain control (AGC)

The signal strength (amplitude) of the radio signal from a receiver's antenna varies drastically, by orders of magnitude, depending on how far away the radio transmitter is, how powerful it is, and propagation conditions along the path of the radio waves. The strength of the signal received from a given transmitter varies with time due to changing propagation conditions of the path through which the radio wave passes, such as multipath interference; this is called fading. Insufficient signal amplitude will cause an increase of noise in the demodulator, while excessive signal amplitude will cause amplifier stages to overload (saturate), causing distortion (clipping) of the signal.

Therefore, almost all modern receivers include a feedback control system which monitors the average level of the radio signal at the detector, and adjusts the gain of the amplifiers to give the optimum signal level for demodulation. (1) the mix of radio signals from the antenna is filtered to extract the signal of the desired transmitter; (2) this oscillating voltage is sent through a radio frequency (RF) amplifier to increase its strength to a level sufficient to drive the demodulator; (3) the demodulator recovers the modulation signal (which in broadcast receivers is an audio signal, a voltage oscillating at an audio frequency rate representing the sound waves) from the modulated radio carrier wave; (4) the modulation signal is amplified further in an audio amplifier, then is applied to a loudspeaker or earphone to convert it to sound waves.

Although the TRF receiver is used in a few applications, it has practical disadvantages which make it inferior to the superheterodyne receiver below, which is used in most applications. is the design used in almost all modern receivers except a few specialized applications.

In the superheterodyne, the radio frequency signal from the antenna is shifted down to a lower "intermediate frequency" (IF), before it is processed. The incoming radio frequency signal from the antenna is mixed with an unmodulated signal generated by a local oscillator (LO) in the receiver. The mixing is done in a nonlinear circuit called the "mixer". The result at the output of the mixer is a heterodyne or beat frequency at the difference between these two frequencies. The process is similar to the way two musical notes at different frequencies played together produce a beat note. This lower frequency is called the intermediate frequency (IF). The IF signal also has the modulation sidebands that carry the information that was present in the original RF signal. The IF signal passes through filter and amplifier stages, The receiver can be designed to receive on either of these two frequencies; if the receiver is designed to receive on one, any other radio station or radio noise on the other frequency may pass through and interfere with the desired signal. A single tunable RF filter stage rejects the image frequency; since these are relatively far from the desired frequency, a simple filter provides adequate rejection. Rejection of interfering signals much closer in frequency to the desired signal is handled by the multiple sharply-tuned stages of the intermediate frequency amplifiers, which do not need to change their tuning.