thumb|Three different international-standard two-hole punches
A hole punch, also known as a hole puncher or paper puncher, is an office tool and item of stationery that is used to create holes in sheets of paper, often for the purpose of collecting the sheets in a binder or folder (such collected sheets are called loose leaves). A hole punch can also refer to similar tools for other materials, such as leather, cloth, or sheets of plastic or metal.
Mechanism
thumb|Mechanism of a typical hole punch
The essential parts of a hole punch are the handle, the punch head, and the die. The punch head is typically a cylinder, with a flat end called the face. The die is a flat plate, with a hole matching the head. The head can move, while the die is fixed in place. Both head and die are usually made of a hard metal, with precise tolerances. One or more sheets of paper are inserted between the head and the die, with the flat face of the head parallel to the surface of the sheets. Moving the handle pushes the head straight through the sheets of paper. The hard edge of the punch vs the die cuts a hole in the paper, pushing the cut piece out the bottom of the die. The cut-out bit of paper scrap is called a chad.
The handle functions as a lever, decreasing the amount of force the operator needs to apply. The travel distance of the cylinder is generally very short—the thickness of the paper sheets—so the cylinder can be positioned close to the lever fulcrum. For low-volume hole punches, the resulting lever handle need not be more than long for sufficient force. Hole punches for larger volumes of paper (hundreds of sheets) feature longer lever arms, but function similarly.
There are hole punches which punch patterns of multiple holes at once, typically for binding multiple sheets together (see ). Such punches generally feature two paper guides for alignment. One guide will be along the side of the paper to be punched, and sets the distance of the holes from the edge of the paper (the margin or gutter). The other guide will be on a perpendicular side, and aligns the holes between the top and bottom of the sheet. One or both guides may be adjustable.
On multiple-hole punches, the positions of individual punch heads may also be adjustable. Commonly, one or more punch heads are mounted in independent fittings, which can slide along a rail. A set screw holds each fitting in position. There may be marks on the device to identify standard hole positions. There may be positions where a punch head will not make contact with the activating handle, allowing holes to be "turned off".
Some punch designs use hollow punch heads (a thin-walled tube), with the edge a sharpened blade. This allows the chads to be pushed up and out the top, as the paper is being cut, making it more suitable for thicker volumes of paper. For very large amounts of paper, a paper drill may be used instead of a punch.
Applications
Single-hole punches
thumb|Common handheld single-hole punch
A single-hole punch makes a single hole per activation, usually at an arbitrary position (i.e., without alignment guides).
Single-hole punches are often used to punch an admission ticket or other document to indicate it has been used or processed. A specialized ticket punch may be used for this purpose. Some ticket punches have a longer reach/depth (allowing for a particular spot on the ticket to be punched), or punch a particular shape instead of a round hole.
Single-hole punches are often used to punch holes through old playing cards at casinos, marking them as "used" or "canceled". This helps cut down on cheating by eliminating any cards that may have been tainted by players.
Single-hole punches are widely used in the British Civil Service where papers are punched with a single hole in the upper left, and secured using a treasury tag.
Single-hole punches can also be used for binding, with a single loose binding ring, although this is much less common than with ring binders.
Single-hole punches can also be used to make confetti for scrapbooks and other crafting.
Eyelet punch
thumb|right|Eyelet punch press
A related office tool is the eyelet punch. This is a single-hole punch which also crimps a metal fastening loop around the hole, similar to a rivet. It is used to permanently secure a few sheets of paper together.
A similar tool, generally known as a holing pincer, is used in animal husbandry. A common application is to attach an ear tag to a livestock animal.
Paper tape repair punch
Specialized hand-operated tape punches were used to perform small edits and repairs on punched paper tapes used for data entry into teletypes or early computers. Torn or damaged tapes were sometimes aligned with specialized jigs, spliced with special adhesive tape, and the holes encoding data were manually restored using such punches. The ASCII character code included a special DELETE or DEL character defined as all holes punched out (code 7F), allowing an erroneous character to be canceled by punching extra holes.
As punched tape technology became obsolescent in the 1980s, the manual tape repair tools became rare.
Multiple-hole punches
Multiple-hole punches typically place a pattern of holes along one edge of sheets of paper, allowing the pages to be bound together.
The most common use for multi-hole punched paper is with a ring binder. A book-like cover is fitted with retaining rings matching the pattern of the punched holes. The rings may be split open, paper sheets threaded onto them, and then the rings closed again.
A related filing option is the presentation folder, which secures punched sheets with built-in prongs or fasteners aligned to common two- or three-hole patterns.
A variety of hole patterns are in use for ring bindings. In much of the world, two-hole and four-hole punches consistent with ISO 838 are the norm. In the US, the three-hole punch is most common. See .
There are other binding techniques which use hole punching. Coil binding uses a spring-like coil, threaded into the punched holes. Comb binding uses a plastic strip with "fingers" that clip into the punched holes. Both use their own types of specialized hole punches. Comb binding typically punches 19 or 23 rectangular holes (for letter and A4 paper sizes, respectively).
<gallery mode="packed">
File:VierfachLocher (fcm).jpg|German four-hole punch
File:Perforator 23-gats.jpg|23-hole punch
</gallery>
Hole punch for discbound notebooks
A hole punch does not necessarily make round or square holes in a sheet of paper; instead, it may create certain shapes along the edge of the sheet. This is seen in discbound notebook systems, where loose leaves are bound together using plastic discs. For more information on loose leaf systems, see Loose leaf.<gallery>
File:Staples ARC hole punch for ARC discbound notebook system.jpg|ARC hole punch for ARC discbound notebook system
File:Binder-based and discbound loose leaf systems.jpg|Binder-based and discbound loose leaf systems
</gallery>
History
The origins of the hole punch date back to Germany; Friedrich Soennecken filed his patent on 14 November 1886, for his , a multiple-hole punch and office supply product.
</references>