The AEREON III was an experimental hybrid airship of rigid construction built by the AEREON Corporation in the early 1960s. Of unconventional design, the airship featured three gas envelopes attached side-by-side, with the connecting structures shaped as airfoils to create extra lift as the craft moved forward. Intended as a small prototype craft that would precede the development of much larger hybrid airships, the AEREON III was constructed between 1959 and 1965 but was destroyed during taxiing tests in 1966 and scrapped without having flown. It was "the first rigid airship to be built since Graf Zeppelin II".
Background
The AEREON Corporation had been founded in 1959 by Presbyterian minister and U.S. Naval Reserve chaplain turned airship enthusiast Monroe Drew and Navy airship veteran Lieutenant Commander John Fitzpatrick. (Aereon II was Andrews's second airship, a single-hulled craft.) at Mercer County Airport in Trenton, New Jersey. The construction work was carried out by Everett Linkenhoker, an airship rigger hired on the recommendation of Aereon's consultant, the distinguished airship aviator and retired U.S. Navy Vice Admiral Charles Rosendahl.
Future versions of the airship were envisaged as being up to long, possibly with nuclear propulsion.
Description
Configuration
The AEREON III comprised three rigid hulls, each in length and in maximum diameter, connected by truss members. The connecting structures between the hulls were faired in an airfoil section, and the aircraft as a whole functioned as an airfoil with an aspect ratio of 0.74. The design was intended to "maximize the dynamic lifting forces acting on the airship hull and to take the fullest advantage of these forces in flight." Each hull contained six gas cells, for a total lifting gas volume of . There were ventral fins with rudders at the aft ends of the outer two hulls and elevons on the trailing edges of the connecting structures. The two-seat cockpit was located in the nose of the central hull. The hulls were enclosed by a double-layer outer cover, comprising an outer Tedlar layer and an inner layer of ripstop nylon treated with dope. The gas cells were also made of Tedlar. The fins were of sheet Duralumin on frames of the same material, joined primarily with epoxy resin rather than by riveting. The engine drove a diameter, two-bladed pusher propeller (actually a helicopter rotor rotating in the vertical plane). The location of the propeller at the aft end of the hull was stated to assist in boundary layer control and its cyclic pitch feature to facilitate low-speed control. However, the propeller required shortening before trials commenced because of its "greatly excessive vibration."
Buoyancy control
Five propane burners in each hull enabled the helium to be heated to increase lift; the ship would be about heavy (i.e. weight greater than static lift) with the gas cells 83 percent filled with helium, but heating the gas would increase the static lift by . The helium could also be cooled by admitting air through vents in the noses of the hulls, with the assistance of blowers. The double-layer outer cover, mentioned above, facilitated thermal insulation of the gas cells.
One source states that the AEREON IIIs buoyancy-control capabilities would allow it to fly using "gravity propulsion"—without the assistance of an engine—along the lines of Solomon Andrews's original Aereon but substituting helium heating for Andrews's dropping of ballast and helium cooling for his valving of hydrogen.
|prime units?=imp
<!--
General characteristics
-->
|genhide=
|crew=2
|capacity=40,000 cu ft
|length ft=85
|length in=0
|length note=
|span ft=56
|span in=
|span sigfig=
|span note=
|height ft=
|height in=
|height sigfig=
|wing area sqm=
|wing area sqft=
|wing area note=
|aspect ratio=
|airfoil=
|empty weight kg=
|empty weight lb=2,800
|empty weight note=
|gross weight kg=
|gross weight lb=
|gross weight note=
|max takeoff weight kg=
|max takeoff weight lb=
|max takeoff weight note=
|fuel capacity=
|more general=
<!--
Powerplant
-->
|eng1 number=1
|eng1 name=Solar Titan
|eng1 type=turbine
|eng1 kw=<!-- prop engines -->
|eng1 hp=70<!-- prop engines -->
|prop blade number=2<!-- propeller aircraft -->
|prop name=Helicom
|prop dia m=<!-- propeller aircraft -->
|prop dia ft=21<!-- propeller aircraft -->
|prop dia in=0<!-- propeller aircraft -->
|prop dia note=reversible-pitch rotor/propeller
|rot number=<!-- helicopters -->
|rot dia m=<!-- helicopters -->
|rot dia ft=<!-- helicopters -->
|rot dia in=<!-- helicopters -->
|rot area sqm=<!-- helicopters -->
|rot area sqft=<!-- helicopters -->
|rot area note=
<!--
Performance
-->
|perfhide=
|max speed kmh=
|max speed mph=65
|max speed kts=
|max speed note=
|max speed mach=<!-- supersonic aircraft -->
|cruise speed kmh=
|cruise speed mph=
|cruise speed kts=
|cruise speed note=
|stall speed kmh=
|stall speed mph=
|stall speed kts=
|stall speed note=
|never exceed speed kmh=
|never exceed speed mph=127
|never exceed speed kts=
|never exceed speed note=
|range km=
|range miles=
|range nmi=
|range note=
|combat range km=
|combat range miles=
|combat range nmi=
|combat range note=
|ferry range km=
|ferry range miles=
|ferry range nmi=
|ferry range note=
|endurance=4 hours<!-- if range unknown -->
|ceiling m=
|ceiling ft=8,500
|ceiling note=
|g limits=<!-- aerobatic -->
|roll rate=<!-- aerobatic -->
|climb rate ms=
|climb rate ftmin=
|climb rate note=
|time to altitude=
|more performance=*Take-off run:
|avionics=
Destruction
On April 15, 1966, the AEREON III was taxiing on a runway at Mercer County Airport in a crosswind when it failed to slow down, tried to turn at the end of the runway, and tilted over onto two wheels. One of the pilots jumped from the cockpit, and the airship then turned flat on its back. The second pilot then jumped straight down from the inverted cockpit, and the airship overturned a second time. According to John McPhee's book The Deltoid Pumpkin Seed, the remains of the AEREON III were "virtually bulldozed back into the hangar, arriving more or less in flakes." However, another source states that reconstruction into a new, larger AEREON IIIB was contemplated. This craft would have been long and in span, with a "metal-clad, partially delta" shape. According to this source, the damaged AEREON III was eventually broken up "sometime in 1967."
The AEREON III was succeeded by the AEREON 26, which had an entirely different, deltoid shape. The new aircraft inherited its predecessor's McCulloch engine, along with aluminum tubing from the structure of AEREON III and several of its instruments. One of the nosecones from AEREON III is reportedly in the Lighter-than-Air Society's collection in Akron, Ohio.
See also
Comparable aircraft:
AEREON 26